Fitting a Cat Flap in a UPVC Door > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Allowing your cat flap installers to go in and out of the house at will is an excellent way to keep your pet active and mentally engaged. A flap can reduce toileting incidents by making it easier for your cat to leave the house if needed.

Measure the Door

A cat flap fitters flap lets your pet to move around whenever they want without having to open the door for them. This makes it perfect to keep them in the house when you're at home or away, and helps keep unwanted pests out of your house as well!

It's important to measure the door before you buy a cat flap as there are various sizes available. You should then make sure that the cat flap is the correct size for your door made of upvc. In the event that it is not, it could be too big or small, and your cat could be unable to use it.

Before you do anything, though, use a ruler to take measurements of the width of the door in various places along its edge. You should also take measurements of the height of the door in a few spots. This is because the door that is too high can cause your cat to perform a gymnast's routine every time they need to use the flap!

Ask a glazier for assistance when you're unsure of how to measure the door. They will be able to assist you in determining whether or not your door is suitable for a cat flap, and advise you on the right size of flap to purchase.

When you've got your measurements, the next step to do is to draw the outline of the hole in the door. This will assist you when you're cutting the hole and will save you money!

It is also important to ensure that the hole you're creating is placed in the right spot. For instance, if you're fitting the cat flap in the patio door, you must ensure that the hole is not too close to hinges, as this can cause leakage and problems with the seal.

It is best to leave the job of installing a cat flap installer flap on glass doors to an experienced glazier. It can be difficult to install a cat flap into an existing glass pane, and you may find that the process causes it to break and lose its weatherproof seal.

Measure the Cat

A cat flap allows your pet to move around whenever they want without having to leave them alone. It can also keep draughts out of your house, which aren't good for either you or your cat!

However, if you have a uPVC or composite door, it can seem tricky to fit the cat flap. These doors are constructed of different materials and the installation is different. Before you think about installing a cat flap in your uPVC or composite door, ensure that it is compatible and that you've checked with the manufacturer as any modifications could invalidate any warranties.

These doors are generally designed to last and are tough, with insulation. This makes them more resistant to elements of the weather than other doors, but they may be difficult to fit a cat flap into. If you're not sure if your uPVC or composite door is able to accommodate a cat flap, consult with a professional jointer prior to beginning.

You'll need to take their height to ensure that they can fit through the door. This is easier when they're sleeping or calm, so that they aren't moving around too often. Once you've determined their height, measure the distance between their stomachs and the floor to determine where the bottom of the cat flap needs to be. This position is marked on the door.

When you use power tools to cut your uPVC or composite door, you have to be careful. The process of drilling into metal could cause cracks, particularly in the case of toughened glass. This is the reason it's recommended to engage an expert glazier to install your cat flap inside glass. This will prevent the glass from becoming brittle or shattering. A glazier will also provide you with a circular hole to use for the cat flap, which will be less likely to crack and is safer for your kitty to use.

Cut the Hole

A good quality cat flap comes with a template drawing that you can use to mark the spot on your door where the hole needs to go. If it does not then you can create one by using an uncoated sheet of paper (tracing paper is ideal). Once the shape has been drawn on the door, you can use your spirit level to make sure that it is horizontal. This will ensure that your cat flap is positioned correctly in the opening, and it will not slide open or close.

Next, take your jigsaw, and cut the shape that has been written on the door. Use a blade that is specifically designed for uPVC doors. It will usually be marked with this information. If not, ask the staff in your DIY store for assistance. Once you have the hole drilled and the flap section is in place, put it against it and push it out to ensure that the action of the flap is smooth. If it binds at any point, use the filer or the rasp to fix this.

Verify that there aren't gas or electric pipes inside the door you plan to cut through. Your jigsaw could cause damage to them. Similarly you should be aware of any handles or other door fixtures that need to be removed to install the cat flap. Be cautious not to scratch them during this process.

The majority of people who install a cat flap themselves will have an ordinary solid uPVC door, and therefore won't have to deal with any of these issues. If your door is constructed of wood or has a decorative piece that isn't easily removed, this will complicate the job.

It is always worth seeking professional assistance from a cat flap fitter for these kind of jobs since it is important to get the job done correctly to avoid possible issues in the future. Making the wrong choice could lead to the door being damaged and could make it impossible to honor the warranty.

Fit the Flap

After you've made your hole drilled, put the flap in place to see if it fits and is able to open easily. If you find any points that stick or catch, use a hand file or sandpaper to file them down until they fit properly and open without difficulty. Make sure that the flap sits in a flush position with the door.

Some kits include templates for this, however, if it doesn't, you can use a piece or thin paper instead, something similar to tracing paper. Place the paper on the door, and draw a line to indicate the location where the flap is placed (this will serve as a cutting guide). Make four screw holes at every corner of the flap using the pencil marks you made on the door. These are the screws will be used to secure the flap to the door.

Most uPVC door are solid and easy to cut. If the door is made of composite or GRP, it can be more difficult. If you're unfamiliar with this then it may be advisable to hire an expert to complete the job for you. They can also provide you with advice on whether or not your particular door is suitable for cat flap installation.

You can install a cat flap - Read Even more - into composite doors but it's important to verify with the manufacturer or a professional joiner first because any changes to these doors could invalidate the warranty. If you decide to complete the work yourself, keep in mind that it could be a messy job and may even be hazardous.

You'll require an instrument like a grinder or a saw to cut through composite doors, rather than only the GRP. Be aware that this can be extremely dangerous work and you'll have to take extreme care not to harm the door or yourself as it is very fragile. It is important to note that it is much more difficult to cut holes in door glass than in a uPVC door or a solid wood doors.